Honda CR-V: To Play a CD

To play CDs, the ignition switch must be in the ACCESSORY (I) or ON (II) position.

You operate the CD changer with the same controls used for the indash disc player or the radio. To select the CD changer, touch the CDC icon. The disc and track numbers are displayed. The system will continuously play a CD until you change modes.

Do not use CDs with adhesive labels.

The label can curl up and cause the CD to jam in the unit.

To select a different disc, use the preset buttons (5 or 6). Press and release the Preset 5 (DISC +) button to select the previous disc or Preset 6 (DISC -) to select the next disc in sequence. Pressing the side of the TUNE bar also or changes the disc. If you select an side of the TUNE bar also changes the disc. If you select an empty position in the CD changer, the system will try to load the CD in the next available slot.

You can use the preset buttons while

You can use the preset buttons while a disc is playing to select passages and change tracks. Each preset button function is shown on the bottom of the screen.

SKIP - Push the (preset 6) to play the next track on button (preset 6) to play the next track on the disc. Push the button button (preset 5) once to replay the track in play; press it twice to replay the previous track.

FF/REW - To move more rapidly within a track, press and hold the (preset 3) (preset 4) or (preset 3) (preset 3) button.

REPEAT (Track Repeat) - To continuously replay a track, press and release the RPT button (preset 1). You will see TRACK REPEAT in the display. Press the RPT button again to turn it off.

DISC REPEAT - To continuously replay the current CD, press and hold the RPT button (preset 1) until you see the DISC REPEAT in the display. Press it again to turn it off.

RANDOM(Track Random) - Press and release the RDM button (preset 2) to play the tracks in random order. You will see TRACK RANDOM in the display. Press the RDM button again to return to normal play.

DISC RANDOM - To play all tracks in each CD in random order, press and hold the RDM button (preset 2) until you see DISC RANDOM in the display. Press the RDM button again to return to normal play.

SCAN (Track Scan) - The SCAN function samples all the tracks on the selected disc in the order they are recorded. To activate it, press and release the SCAN button. You will see TRACK SCAN in the display, and you will get a 10 second sampling of each track on the selected CD. Press the SCAN button again to get out of scan mode.

DISC SCAN - Press and hold the SCAN button to get a 10 second sampling of the first song of each disc in the CD changer. You will see DISC SCAN in the display. Press and hold the button again to turn it off.

READ NEXT:

 To Stop Playing a CD

Press the AM/FMor CD/XM button to switch to the radio or satellite radio while a CD is playing. If there is a PC card in the audio unit, touch the CARD icon to switch to the PC card while a C

 CD Changer Error Messages (EX-L model with navigation system)

If you see an error message in the display while playing a disc, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. The cha

 Playing a PC card (EX-L model with navigation system)

Playing a PC card (EX-L model with navigation system)

SEE MORE:

 Transfer Assembly Inspection/Removal/Installation

Transfer Assembly Inspection 1. Shift the transmission into the N position. 2. Raise the vehicle on a lift, and make sure it is supported securely. 3. Make a reference mark (A) across the propeller shaft (B) and the transfer companion flange (C). 4. Separate the propeller shaft from the transfer

 PSP Switch Signal Circuit Troubleshooting

1. Start the engine, and let it idle. 2. Align the steering wheel straight ahead. 3. Check the PSP SWITCH in the DATA LIST with the HDS. Does it indicate ON? YES-Go to step 4. NO-Go to step 14. 4. Turn the steering wheel to the full lock position. 5. Check the PSP SWITCH in the DATA LIST with t

© 2016-2024 Copyright www.hcrv.net